China manufacturer CZPT OEM 2901021300 1613688001 Screw Air Compressor Parts Air Oil Separator threaded shaft and captive nut

Product Description

 

 

Product Description

 

Atlas Copco OEM 29571213 Screw Air Compressor Parts Air Oil Separator

Oil separator is used for CZPT Air Compressor

It uses the combination of high and low precision fiberglass filter paper, wound more than 10 layers of fiberglass filter paper in the middle net as the main filter layer.
The oil mist in the compressed air is intercepted, collided, diffused and gathered. Small oil droplets quickly gather into large oil droplets, which pass through the polymerization layer under the push of pneumatic and gravity, and accumulate at the bottom of the filter element. Then, the oil return pipe inlet at the bottom of the filter element is returned to the lubrication system.
 

Product name Air Oil Separator
Material Superfine glass fiber CZPT filter material
Service life >4000H
Filtering precision ≤0.1um
Filtration efficiency 99.99%
Print Print the part number on the bottom or as request

Replacement method of oil air separator

 

External models:

Stop the air compressor, close the air pressure outlet, open the drain valve, and after confirming that the system is pressure-free, remove the old oil and gas separator and replace it with a new one.

1. There is a safety valve on the end cover of the oil separation tank of the air compressor. When the air pressure in the oil separation tank reaches 1.1 times the set value, the safety valve will automatically open to release part of the air and reduce the air pressure in the oil separation tank. The method to check the safety valve is to gently pull the vent lever on the safety valve when the compressor is working at full load. If the safety valve can discharge outward, it is considered normal.

2. There is a pressure gauge on the oil separation tank to detect the pre-filter pressure. The bottom of the oil separation tank is equipped with a drain valve. The drain valve should be opened regularly to let off the water and dirt deposited on the bottom of the oil separation tank.

3. There is a transparent oil level mirror beside the oil separation tank to show the level of the oil separation tank. The correct oil level is when the air compressor is working normally, the oil level is in the middle of the upper and lower degrees. If it is too high, it will run away, and if it is too low, it will affect the safety of the whole machine.

4. The oil separation tank is produced by a professional manufacturer that must have manufacturing qualifications for pressure vessels.

 

Detailed Photos

 

 

 

Our Advantages

 

 

Company Profile

       
        Filters are part of the air handling system and can provide the clean compressed air needed to remove oil and impurities. It can be used not only in pneumatic systems and pneumatic tools, but also in food, pharmaceutical and other industries. 

       Now over 100,000 quality filters including compressed air filters, Hydraulic Filters and complete filter housing assemblies at wholesale discounts. We offer OEM products as well as high quality replacements, engineered to precise OEM specifications and guaranteed to match the exact form, fit and function as the original equipment. 

      Our company is committed to continuous innovation and further improvement to create, improve the efficiency and productivity of excellence, to achieve the highest level of reliability and performance.

 

 

Packaging & Shipping

 

Certifications

 

FAQ

 

Q: What is the online order minimum?
A: Currently our online order minimum is 1 pcs.
Q: Do you sell parts for engine driven portable air compressors too?
A: No, at this time we only carry parts for electric motor driven stationary compressors.
Q: What brands do you carry parts for?
A: We handle replacement parts for every major air compressor manufacturer such as Atlas Copco, Compair, Gardner Denver, Ingersoll Rand,  Kaeser, Quincy, Sullair, Worthington and many more. If you don’t see your brand listed, just give us a call and we’ll try to help locate your part.
Q: How long is your delivery time?
A: If there is stock, the lead time is about 2 working days after we get the payment. The specific delivery time depends on models and the quantity of your order.

Customized: Customized
Standard Component: Standard Component
Material: Fiber Glass
Category: Oil Separator
Part Number: 2989004800
Product Name: Air Oil Separator
Customization:
Available

|

Customized Request

screwshaft

Screw Shaft Types and Uses

Various uses for the screw shaft are numerous. Its major diameter is the most significant characteristic, while other aspects include material and function are important. Let us explore these topics in more detail. There are many different types of screw shafts, which include bronze, brass, titanium, and stainless steel. Read on to learn about the most common types. Listed below are some of the most common uses for a screw shaft. These include: C-clamps, screw jacks, vises, and more.

Major diameter of a screw shaft

A screw’s major diameter is measured in fractions of an inch. This measurement is commonly found on the screw label. A screw with a major diameter less than 1/4″ is labeled #0 to #14; those with a larger diameter are labeled fractions of an inch in a corresponding decimal scale. The length of a screw, also known as the shaft, is another measure used for the screw.
The major diameter of a screw shaft is the greater of its two outer diameters. When determining the major diameter of a screw, use a caliper, micrometer, or steel rule to make an accurate measurement. Generally, the first number in the thread designation refers to the major diameter. Therefore, if a screw has a thread of 1/2-10 Acme, the major diameter of the thread is.500 inches. The major diameter of the screw shaft will be smaller or larger than the original diameter, so it’s a good idea to measure the section of the screw that’s least used.
Another important measurement is the pitch. This measures the distance between one thread’s tip and the next thread’s corresponding point. Pitch is an important measurement because it refers to the distance a screw will advance in one turn. While lead and pitch are two separate concepts, they are often used interchangeably. As such, it’s important to know how to use them properly. This will make it easier to understand how to select the correct screw.
There are three different types of threads. The UTS and ISO metric threads are similar, but their common values for Dmaj and Pmaj are different. A screw’s major diameter is the largest diameter, while the minor diameter is the lowest. A nut’s major diameter, or the minor diameter, is also called the nut’s inside diameter. A bolt’s major diameter and minor diameter are measured with go/no-go gauges or by using an optical comparator.
The British Association and American Society of Mechanical Engineers standardized screw threads in the 1840s. A standard named “British Standard Whitworth” became a common standard for screw threads in the United States through the 1860s. In 1864, William Sellers proposed a new standard that simplified the Whitworth thread and had a 55 degree angle at the tip. Both standards were widely accepted. The major diameter of a screw shaft can vary from one manufacturer to another, so it’s important to know what size screw you’re looking for.
In addition to the thread angle, a screw’s major diameter determines the features it has and how it should be used. A screw’s point, or “thread”, is usually spiky and used to drill into an object. A flat tipped screw, on the other hand, is flat and requires a pre-drilled hole for installation. Finally, the diameter of a screw bolt is determined by the major and minor diameters.
screwshaft

Material of a screw shaft

A screw shaft is a piece of machine equipment used to move raw materials. The screw shaft typically comprises a raw material w. For a particular screw to function correctly, the raw material must be sized properly. In general, screw shafts should have an axial-direction length L equal to the moving amount k per 1/2 rotation of the screw. The screw shaft must also have a proper contact angle ph1 in order to prevent raw material from penetrating the screw shaft.
The material used for the shaft depends on its application. A screw with a ball bearing will work better with a steel shaft than one made of aluminum. Aluminum screw shafts are the most commonly used for this application. Other materials include titanium. Some manufacturers also prefer stainless steel. However, if you want a screw with a more modern appearance, a titanium shaft is the way to go. In addition to that, screws with a chromium finish have better wear resistance.
The material of a screw shaft is important for a variety of applications. It needs to have high precision threads and ridges to perform its function. Manufacturers often use high-precision CNC machines and lathes to create screw shafts. Different screw shafts can have varying sizes and shapes, and each one will have different applications. Listed below are the different materials used for screw shafts. If you’re looking for a high-quality screw shaft, you should shop around.
A lead screw has an inverse relationship between contact surface pressure and sliding velocity. For heavier axial loads, a reduced rotation speed is needed. This curve will vary depending on the material used for the screw shaft and its lubrication conditions. Another important factor is end fixity. The material of a screw shaft can be either fixed or free, so make sure to consider this factor when choosing the material of your screw. The latter can also influence the critical speed and rigidity of the screw.
A screw shaft’s major diameter is the distance between the outer edge of the thread and the inner smooth part. Screw shafts are typically between two and sixteen millimeters in diameter. They feature a cylindrical shape, a pointy tip, and a wider head and drive than the former. There are two basic types of screw heads: threaded and non-threaded. These have different properties and purposes.
Lead screws are a cost-effective alternative to ball screws, and are used for low power and light to medium-duty applications. They offer some advantages, but are not recommended for continuous power transmission. But lead screws are often quieter and smaller, which make them useful for many applications. Besides, they are often used in a kinematic pair with a nut object. They are also used to position objects.
screwshaft

Function of a screw shaft

When choosing a screw for a linear motion system, there are many factors that should be considered, such as the position of the actuator and the screw and nut selection. Other considerations include the overall length of travel, the fastest move profile, the duty cycle, and the repeatability of the system. As a result, screw technology plays a critical role in the overall performance of a system. Here are the key factors to consider when choosing a screw.
Screws are designed with an external threading that digs out material from a surface or object. Not all screw shafts have complete threading, however. These are known as partially threaded screws. Fully threaded screws feature complete external threading on the shaft and a pointed tip. In addition to their use as fasteners, they can be used to secure and tighten many different types of objects and appliances.
Another factor to consider is axial force. The higher the force, the bigger the screw needs to be. Moreover, screws are similar to columns that are subject to both tension and compression loads. During the compression load, bowing or deflection is not desirable, so the integrity of the screw is important. So, consider the design considerations of your screw shaft and choose accordingly. You can also increase the torque by using different shaft sizes.
Shaft collars are also an important consideration. These are used to secure and position components on the shaft. They also act as stroke limiters and to retain sprocket hubs, bearings, and shaft protectors. They are available in several different styles. In addition to single and double split shaft collars, they can be threaded or set screw. To ensure that a screw collar will fit tightly to the shaft, the cap must not be overtightened.
Screws can be cylindrical or conical and vary in length and diameter. They feature a thread that mates with a complementary helix in the material being screwed into. A self-tapping screw will create a complementary helix during driving, creating a complementary helix that allows the screw to work with the material. A screw head is also an essential part of a screw, providing gripping power and compression to the screw.
A screw’s pitch and lead are also important parameters to consider. The pitch of the screw is the distance between the crests of the threads, which increases mechanical advantage. If the pitch is too small, vibrations will occur. If the pitch is too small, the screw may cause excessive wear and tear on the machine and void its intended purpose. The screw will be useless if it can’t be adjusted. And if it can’t fit a shaft with the required diameter, then it isn’t a good choice.
Despite being the most common type, there are various types of screws that differ in their functions. For example, a machine screw has a round head, while a truss head has a lower-profile dome. An oval-its point screw is a good choice for situations where the screw needs to be adjusted frequently. Another type is a soft nylon tip, which looks like a Half-dog point. It is used to grip textured or curved surfaces.

China manufacturer CZPT OEM 2901021300 1613688001 Screw Air Compressor Parts Air Oil Separator   threaded shaft and captive nutChina manufacturer CZPT OEM 2901021300 1613688001 Screw Air Compressor Parts Air Oil Separator   threaded shaft and captive nut
editor by CX 2023-11-13

Recent Posts